You can drill a hole and push screws with the same tool if it’s cordless, and you won’t have to worry about locating a socket near your job to power it. With so many various drill/driver models available, it’s easy to purchase more than you need.

The option is to purchase a drill based on your intended purpose. It makes no sense to spend $200 on a tool that will only be used to hang posters. It’s also not a good idea to spend $50 on a drill only to have the motor fail after a few hours of heavy use.

Table of Contents

• What Are The Different Types of Drills
• What Features To Look For In A Drill
• Our Handpicked Cordless Drills
  • BLACK+DECKER 20V MAX Cordless Drill / Driver with 30-Piece Accessories (LD120VA)
  • BOSCH Power Tools Drill Kit – PS31-2A – 12V, 3/8 Inch, Two Speed Driver, Cordless Drill Set
  • Makita XFD131 18V LXT Lithium-Ion Brushless Cordless 1/2 In. Driver-Drill Kit
  • K I M O Cordless Drill/Driver Kit Li-Ion Battery and Charger – 12V MAX Drill 280 In-lb Torque

What Are The Different Types of Drills

Drills/drivers are tools that are used to drill holes and drive screws into wood, metals, or plastics. It is the most common type, and it’s what we’ll be looking at. Hammer drills perform the same thing, but they also feature a hammer mode that shakes the drill bit in and out for masonry drilling. They are slightly heavier than drills/drivers.

What Features To Look For In A Drill

Power – For cordless drills, power is calculated in battery voltage. To overcome resistance, more voltage means more torque-spinning strength. Drills with a greater voltage may bore large holes in construction timber and carpet. That’s a lot of strength. However, there is a cost to having more power: weight. A 9.6V drill weighs about 3 1/2 pounds, whereas an 18V drill can weigh up to 10 pounds.

Handle – The base of the handle flares out to minimize hand slippage and to make room for a battery. A T-handle provides better optimal balance, especially in bigger drills, so because the battery is situated beneath the weight and mass of the engine

Clutch – This prevents you from overtightening or shattering a screw. A broad range of clutch settings is essential because the clutch must slip when the torque on the screw gets too high, preventing the drill head from rotating.

Reverse– To remove screws from wood or other materials, you’ll need this tool. Without adjusting your grip, you must be capable of reaching the rotating switch or button using your thumb or fingers.

Motor– A brushless motor has a high efficiency, which means increased durability, power, durability, and less maintenance. Brushless motors are also lighter and quiet than traditional motors. A built-in light helps you see where you’re drilling or driving.

Our Handpicked Cordless Drills

The selection below includes cordless drills that we can attest to ourselves, so you can rest assured that they will do well in any scenario.

BLACK+DECKER 20V MAX Cordless Drill / Driver with 30-Piece Accessories (LD120VA)

Cordless drill with Lithium-Ion Battery that is always ready and holds a charge for up to 18 months. The 24 position clutch of this power drill prevents stripping and overdriving screws by providing an extra level of control. This thing battles along really well. powerful. The size and weight make it very easy to use. It’s quiet and easy to handle.

Voltage	20 Volts
Speed	750 RPM

BOSCH Power Tools Drill Kit – PS31-2A – 12V, 3/8 Inch, Two Speed Driver, Cordless Drill Set

The BOSCH PS31 12 Volt Max 3/8 inches cordless drill/driver kit has professional-grade power for 90 percent of tasks, but only weighs just over 2 lbs. An ideal tool to carry to any worksite, this tool, with its 2 speeds and 20+1 torque settings, is a carry-along solution for applications such as installing and electrical work that requires a great deal of overhead drilling and driving.

Voltage	12 Volts
Speed	1300 RPM

Makita XFD131 18V LXT Lithium-Ion Brushless Cordless 1/2 In. Driver-Drill Kit

The Makita 18V LXT Lithium-Ion Brushless cordless ½” driver-drill kit (XFD131) is ideal drilling and driving solution for the user who wants a drill with a superior power-to-weight ratio. the adjustable torque settings provide more control for a full range of applications, from large fasteners to smaller, delicate screws. It weighs only 3.8 lbs. (With a 3.0Ah battery) for increased comfort and a superior power-to-weight ratio. The XFD131 is compatible with Makita 18V LXT Lithium-Ion batteries, from the fast-charging.

Voltage	18 Volts
Speed	900 RPM

K I M O Cordless Drill/Driver Kit Li-Ion Battery and Charger – 12V MAX Drill 280 In-lb Torque

The most compact (7-in from chuck to back) and lightweight (1.8-lb) drill/driver in 12V-class with amazing performance-to-weight ratio, minimizes fatigue in most daily jobs; rubber-covered handle with ergonomic design provides maximum comfort grip for being breezily operated in one hand and less vibration; it maneuverable and simply easy to use for women, not to mention for men. Trigger-activated LED light illuminates any enclosed workspace.